锐捷网络交换机的配置命令集 | 您所在的位置:网站首页 › 锐捷交换机no switchport › 锐捷网络交换机的配置命令集 |
转自:http://hi.baidu.com/bjgbd 交换机 >Enable 进入特权模式 #Exit 返回上一级操作模式 #End 返回到特权模式 #write memory 或copy running-config startup-config 保存配置文件 #del flash:config.text 删除配置文件(交换机及1700系列路由器) #erase startup-config 删除配置文件(2500系列路由器) #del flash:vlan.dat 删除Vlan配置信息(交换机) #Configure terminal 进入全局配置模式 (config)# hostname switchA 配置设备名称为switchA (config)#banner motd & 配置每日提示信息 &为终止符 (config)#enable secret level 1 0 star 配置远程登陆密码为star (config)#enable secret level 15 0 star 配置特权密码为star Level 1为普通用户级别,可选为1~15,15为最高权限级别;0表示密码不加密 (config)#enable services web-server 开启交换机WEB管理功能 Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等 查看信息 #show running-config 查看当前生效的配置信息 #show interface fastethernet 0/3 查看F0/3端口信息 #show interface serial 1/2 查看S1/2端口信息 #show interface 查看所有端口信息 #show ip interface brief 以简洁方式汇总查看所有端口信息 #show ip interface 查看所有端口信息 #show version 查看版本信息 #show mac-address-table 查看交换机当前MAC地址表信息 #show running-config 查看当前生效的配置信息 #show vlan 查看所有VLAN信息 #show vlan id 10 查看某一VLAN (如VLAN10)的信息 #show interface fastethernet 0/1 switchport 查看某一端口模式(如F 0/1) #show aggregateport 1 summary 查看聚合端口AG1的信息 #show spanning-tree 查看生成树配置信息 #show spanning-tree interface fastethernet 0/1 查看该端口的生成树状态 #show port-security 查看交换机的端口安全配置信息 #show port-security address 查看地址安全绑定配置信息 #show ip access-lists listname 查看名为listname的列表的配置信息 #show access-lists 端口的基本配置 (config)#Interface fastethernet 0/3 进入F0/3的端口配置模式 (config)#interface range fa 0/1-2,0/5,0/7-9 进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式 (config-if)#speed 10 配置端口速率为10M,可选10,100,auto (config-if)#duplex full 配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应) (config-if)#no shutdown 开启该端口 (config-if)#switchport access vlan 10 将该端口划入VLAN10中,用于VLAN (config-if)#switchport mode trunk 将该端口设为trunk模式,用于Tag vlan 可选模式为access , trunk (config-if)#port-group 1 将该端口划入聚合端口AG1中,用于聚合端口 聚合端口的创建 (config)# interface aggregateport 1 创建聚合接口AG1 (config-if)# switchport mode trunk 配置并保证AG1为 trunk 模式 (config)#int f0/23-24 (config-if-range)#port-group 1 将端口(端口组)划入聚合端口AG1中 生成树 (config)#spanning-tree 开启生成树协议 (config)#spanning-tree mode stp 指定生成树类型为stp 可选模式stp , rstp , mstp (config)#spanning-tree priority 4096 设置交换机的优先级为4096 , 优先级值小为高。优先级可选值为0,4096,8192,……,为4096的倍数。交换机默认值为32768 VLAN的基本配置 (config)#vlan 10 创建VLAN10 (config-vlan)#name vlanname 命名VLAN为vlanname (config-if)#switchport access vlan 10 将该端口划入VLAN10中 某端口的接口配置模式下进行 (config)#interface vlan 10 进入VLAN 10的虚拟端口配置模式 (config-if)# ip address 192.168.1.1 255.255.255.0 为VLAN10的虚拟端口配置IP及掩码,二层交换机只能配置一个IP,此IP是作为管理IP使用,例如,使用Telnet的方式登录的IP地址 (config-if)# no shutdown 启用该端口 端口安全 (config)# interface fastethernet 0/1 进入一个端口 (config-if)# switchport port-security 开启该端口的安全功能 1.配置最大连接数限制 (config-if)# switchport port-secruity maxmum 1 配置端口的最大连接数为1,最大连接数为128 (config-if)# switchport port-secruity violation shutdown 配置安全违例的处理方式为shutdown,可选为protect (当安全地址数满后,将未知名地址丢弃)、restrict(当违例时,发送一个Trap通知)、shutdown(当违例时将端口关闭,并发送Trap通知,可在全局模式下用errdisable recovery来恢复) 2.IP和MAC地址绑定 (config-if)#switchport port-security mac-address xxxx.xxxx.xxxx ip-address 172.16.1.1 接口配置模式下配置MAC地址xxxx.xxxx.xxxx和IP172.16.1.1进行绑定(MAC地址注意用小写) 三层路由功能(针对三层交换机) (config)# ip routing 开启三层交换机的路由功能 (config)# interface fastethernet 0/1 (config-if)# no switchport 开启端口的三层路由功能(这样就可以为某一端口配置IP) (config-if)# ip address 192.168.1.1 255.255.255.0 (config-if)# no shutdown 三层交换机路由协议 (config)# ip route 172.16.1.0 255.255.255.0 172.16.2.1 配置静态路由 注:172.16.1.0 255.255.255.0 为目标网络的网络号及子网掩码 172.16.2.1 为下一跳的地址,也可用接口表示,如ip route 172.16.1.0 255.255.255.0 serial 1/2(172.16.2.0所接的端口) (config)# router rip 开启RIP协议进程 (config-router)# network 172.16.1.0 申明本设备的直连网段信息 (config-router)# version 2 开启RIP V2,可选为version 1(RIPV1)、version 2(RIPV2) (config-router)# no auto-summary 关闭路由信息的自动汇总功能(只有在RIPV2支持) (config)# router ospf 开启OSPF路由协议进程(针对1762,无需使用进程ID) (config)# router ospf 1 开启OSPF路由协议进程(针对2501,需要加OSPF进程ID) (config-router)# network 192.168.1.0 0.0.0.255 area 0 申明直连网段信息,并分配区域号(area0为骨干区域) IP ACL: 交换机采用命名的访问控制列表;分标准(stand)和扩展(extended)两种 1.标准ACL (config)#ip access-list stand listname 定义命名标准列表,命名为listname,stand为标准列表 (config-std-nacl)#deny 192.168.30.0 0.0.0.255 拒绝来自192.168.30.0网段的IP流量通过 注:deny:拒绝通过;可选:deny(拒绝通过)、permit(允许通过) 192.168.30.0 0.0.0.255:源地址及源地址通配符;可使用any表示任何IP (config-std-nacl)#permit any (config-std-nacl)#end 返回 2.扩展ACL (config)#ip access-list extended listname 定义命名扩展列表,命名为listname,extended为扩展 (config-ext-nacl)#deny tcp 192.168.30.0 0.0.0.255 192.168.10.0 0.0.0.255 eq www 拒绝源地址为192.168.30.0网段的IP访问目的地址为192.168.10.0网段的WWW服务 注:deny:拒绝通过,可选:deny(拒绝通过)、permit(允许通过) tcp: 协议名称,协议可以是udp, ip,eigrp, gre, icmp, igmp, igrp等等。 192.168.10.0 0.0.0.255:源地址及源地址通配符 192.168.30.0 0.0.0.255:目的地址及目的地址通配符 eq:操作符(lt-小于,eq-等于,gt-大于,neg-不等于,range-包含) www:端口号,可使用名称或具体编号 可以使用的协议名称(或编号)和端口名称(或编号)请打?查询。 (config-ext-nacl)#permit ip any any 允许其它通过 (config-ext-nacl)#end 返回 (config)#interface vlan 10 进入端口配置模式 (config-if)# ip access-group listname in 访问控制列表在端口下in方向应用;可选:in(入栈)、out(出栈) (config-if)#end 返回 注:配置ACL时,若只想对其中部分IP进行限制访问时,必须配置允许其流量通过,否则设备只会对限制IP进行处理,不会对非限制IP进行允许通过处理。 在锐捷交换机上配置vrrp、arp和mstp 交换机 密码1234(config)#enable secret level 1 0 1001234(config)#enable secret level 15 0 100远程登入密码1234(config)#line vty 0 41234(config-line)#password 1001234(config-line)#end交换机管理IP1234(config)#interface vlan 11234(config-if)#ip address 192.168.1.10 255.255.255.01234(config-if)#no shutdown修改交换机老化时间1234(config)#mac-address-table aging-time 201234(config)#end添删vlan1234(config)#vlan 8881234(config-vlan)#name a8881234(config)#no vlan 888添加access口1234(config)#interface gigabitEthernet 0/101234(config-if)#switchport mode access1234(config-if)#switchport access vlan 10切换assess trunk1234(config-if)#switchport mode access1234(config-if)#switchport mode trunk指定特定一个native vlan1234(config-if)#switchport trunk native vlan 10配置trunk口的许可vlan列表1234(config-if)#switchport trunk allowed vlan ?add Add VLANs to the current listall All VLANsexcept All VLANs except the followingremove Remove VLANs from the current list速成树协议1234(config)#spanning-tree1234(config)#spanning-tree mode rstp/stp配置网关:switch(config)#ip default-gateway 192.168.1.254 交换机基本配置-常见查看命令查看CPU利用率show cpu 查看交换机时钟show clock 查看交换机日志show logging 查看交换机动态学习到的MAC地址表 show mac-address-table dynamic 查看当前交换机运行的配置文件show running-config 查看交换机硬件、软件信息show version查看交换机的arp表show arp显示接口详细信息的命令show interfaces gigabitEthernet 4/1 counters接口配置Switch(config)#interface gigabitethernet 0/1 把接口工作模式改为光口。Switch(config-if)#medium-type fiber把接口工作模式改为电口。Switch(config-if)#medium-type copper速度/双工配置进入接口配置模式。Switch(config)#interface interface-id设置接口的速率参数,或者设置为auto。 Switch(config-if)#speed {10 | 100 | 1000 | auto } 设置接口的双工模式。Switch(config-if)#duplex {auto | full | half} 例子Switch(config)#interface gigabitethernet 0/1 Switch(config-if)#speed 1000Switch(config-if)#duplex full 光口不能修改速度和双工配置,只能auto。在故障处理的时候,如果遇到规律性的时断时续或掉包,在排除其他原因后,可以考虑是否和对端设备的速率和双工模式不匹配,尤其是两端设备为不同厂商的时候。VLAN建立VLAN 100Switch (config)#vlan 100该VLAN名称为ruijieSwitch (config)#name ruijie将交换机接口划入VLAN 中:range表示选取了系列端口1-48,这个对多个端口进行相同配置时非常有用。Switch (config)#interface range f 0/1-48 将接口划到VLAN 100中。Switch (config-if-range)#switchport access vlan 100 将接口划回到默认VLAN 1中,即端口初始配置。Switch (config-if-range)#no switchport access vlan Switch(config)#interface fastEthernet 0/1该端口工作在access模式下Switch(config-if)#switchport mode access 该端口工作在trunk模式下Switch(config-if)#switchport mode trunk Switch(config)#interface fastEthernet 0/2设定VLAN要修剪的VLAN。Switch(config-if)#switchport trunk allowed vlan remove 2-9,11-19,21-4094取消端口下的VLAN修剪。Switch(config-if)#no switchport trunk allowed vlan 生成树开启生成树协议。Switch(config)#spanning-tree禁止生成树协议。Switch(config)#no spanning-tree配置生成树优先级:配置设备优先级为4096。Switch(config)#spanning-tree priority 4096 数值越低,优先级别越高。端口镜像配置G0/2为镜像端口。Switch (config)# monitor session 1 destination interface G 0/2配置G0/1为被镜像端口,且出入双向数据均被镜像。Switch (config)# monitor session 1 source interface G 0/1 both去掉镜像1。Switch (config)# no monitor session 1 端口聚合Switch(config)#interface fastEthernet 0/1把端口f0/1加入到聚合组1中。Switch (config-if)#port-group 1把端口f0/1从聚合组1中去掉Switch (config-if)#no port-group 1建立ACL:建立ACL访问控制列表名为ruijie,extend表示建立的是扩展访Switch(config)# Ip access-list exten ruijie 问控制列表。添加ACL的规则:禁止PING IP地址为192.168.1.1的设备。Switch (config-ext-nacl)#deny icmp any 192.168.1.1 255.255.255.0 禁止端口号为135的应用。Switch (config-ext-nacl)# deny tcp any any eq 135禁止协议为www的应用。Switch (config-ext-nacl)#deny udp any any eq www 允许所有行为。Switch(config-ext-nacl)# permit ip any any将ACL应用到具体的接口上:Switch (config)#interface range f 0/1把名为ruijie的ACL应用到端口f 0/1上。Switch (config-if)#ip access-group ruijie in 从接口去除ACL。 Switch (config-if)#no ip access-group ruijie in 删除ACL:删除名为ruijie的ACL。Switch(config)#no Ip access-list exten ruijie 增加ACE项后,是增加到ACL最后,不可以中间插入,如果要调整ACE的顺序,必须整个删除ACL后再重新配置。端口安全Switch (config)#interface range f 0/1开启端口安全。Switch(config-if)# switchport port-security 关闭端口安全。Switch(config-if)# no switchport port-security设置端口能包含的最大安全地址数为8。Switch(config-if)# switchport port-security maximum 8 在接口fastethernet0/1配置一个安全地址00d0.f800.073c,并为其绑定一个IP地址192.168.1.1 Switch(config-if)# switchport port-security mac-address 00d0.f800.073c ip-address 192.168.1.1删除接口上配置的安全地址。Switch(config-if)#no switchport port-security mac-address 00d0.f800.073c ip-address 192.168.1.1 防ARP攻击IP和MAC地址的绑定Switch(config)#arp ip-address hardware-address [type] interface-idSwitch(config)#arp 192.168.12.111 00d0.f800.073c arpa g 0/1绑定网关进入指定端口进行配置。Switch(config)#Interface interface-id配置防止ip-address的ARP欺骗。Switch(config-if)#Anti-ARP-Spoofing ip ip-address防STP攻击进入端口Fa0/1。Switch(config)# inter fastEthernet 0/1 打开该端口的的BPDU guard功能。Switch(config-if)# spanning-tree bpduguard enable 关闭该端口的的BPDU guard功能。 Switch(config-if)# spanning-tree bpduguard diaable端口关闭后只能shutdown然后再no shutdown或者重新启动交换机才能恢复! 防DOS/DDOS攻击进入端口Fa0/1。 Switch(config)# inter fastEthernet 0/1 预防伪造源IP的DOS攻击的入口过滤功能。Switch(config-if)#ip deny spoofing-source关闭入口过滤功能只能在三层接口上配置。Switch(config-if)#no ip deny spoofing-source 和ACL不能同时存在。端口关闭后只能shutdown然后再no shutdown或者重新启动交换机才能恢复!防IP扫描攻击配置:打开系统保护。Switch(config)#system-guard enable关闭系统保护功能。Switch(config)#no system-guardDHCP配置打开DHCP Relay Agent: Switch(config)#service dhcp 配置DHCP Server的IP地址: Switch(config)#ip helper-address address VRRP配置Switch(config)#Interface interface-id Switch(config-if)#Standby [group-number] ip ip-address 设置虚拟机的优先级。standby [group-number] priority priority 三层交换机配置SVI:把VLAN 10配置成SVI。switch (config)#interface vlan 10给该SVI接口配置一个IP地址switch (config-if)#ip address 192.168.1.1 255.255.255.0 Routed Port: switch (config)#interface fa 0/1把f 0/1变成路由口。switch (config-if)#no switch 路由配置:添加一条路由。switch (config)#ip route 目的地址 掩码 下一跳 switch (config)#ip route 210.10.10.0 255.255.255.0 218.8.8.8 配置多生成树协议:switch(config)#spanning-tree //开启生成树协议switch(config)#spanning-tree mst configuration //建立多生成树协议switch(config-mst)#name ruijie //命名为ruijieswitch(config-mst)#revision 1 //设定校订本为1switch(config-mst)#instance 0 vlan 10,20 //建立实例0switch(config-mst)#instance 1 vlan 30,40 //建立实例1switch(config)#spanning-tree mst 0 priority 4096 //设置优先级为4096switch(config)#spanning-tree mst 1 priority 8192 //设置优先级为8192switch(config)#interface vlan 10switch(config-if)#vrrp 1 ip 192.168.10.1 //此为vlan 10的IP地址switch(config)#interface vlan 20switch(config-if)#vrrp 1 ip 192.168.20.1 //此为vlan 20的IP地址switch(config)#interface vlan 30switch(config-if)#vrrp 2 ip 192.168.30.1 //此为vlan 30的IP地址(另一三层交换机)switch(config)#interface vlan 40switch(config-if)#vrrp 2 ip 192.168.40.1 //此为vlan 40的IP地址(另一三层交换机) 此配置需在两个三层交换机和二层交换机上进行配置!在二层交换机上不用配置VRRP! 冗余链路 在骨干网设备连接中,单一链路的连接很容易实现,但一个简单的故障就会造成网络的中断.因此在实际网络组建的过程中,为了保持网络的稳定性,在多台交换机组成的网络环境中,通常都使用一些备份连接,以提高网络的健壮性、稳定性. 这里的备份连接也称为备份链路或者冗余链路.备份链路之间的交换机经常互相连接,形成一个环路,通过环路可以在一定程度上实现冗余. 链路的冗余备份能为网络带来健壮性、稳定性和可靠性等好处,但是备份链路也会使网络存在环路,环路问题是备份链路所面临的最为严重的问题,交换机之间的环路将导致网络新问题的发生: 广播风暴 多帧复制 地址表的不稳定 解决方法: 生成树协议避免环路 每个LAN都会选择一台设备为指定交换机,通过该设备的端口连接到根,该端口为指定端口( Designated port ) 将交换网络中所有设备的根端口(RP)和指定端口(DP)设为转发状态(Forwarding),将其他端口设为阻塞状态(Blocking) 生成树经过一段时间(默认值是50秒左右)稳定之后,所有端口要么进入转发状态,要么进入阻塞状态。 IEEE 802.1w—快速生成树协议 快速生成树协议概述 快速生成树协议RSTP(Rapid Spannning Tree Protocol) IEEE 802.1w RSTP协议在STP协议基础上做了改进,使得收敛速度快得多(最快1秒以内) 生成树协议的配置 开启生成树协议 Switch(config)#Spanning-tree 关闭生成树协议 Switch(config)#no Spanning-tree 配置生成树协议的类型 Switch(config)#Spanning-tree mode stp/rstp 锐捷全系列交换机默认使用MSTP协议 配置交换机优先级 Switch(config)#spanning-tree priority (“0”或“4096”的倍数、共16个、缺省32768) 恢复到缺省值 Switch(config)# no spanning-tree priority 配置交换机端口的优先级 Switch(config)#interface interface-type interface-number Switch(config-if)#spanning-tree port-priority number 显示生成树状态 Switch#show spanning-tree 显示端口生成树协议的状态 Switch#show spanning-tree interface fastethernet 生成树协议概述 生成树协议(spanning-tree protocol)由IEEE 802.1d标准定义 生成树协议的作用是为了提供冗余链路,解决网络环路问题 生成树协议通过SPA(生成树算法)生成一个没有环路的网络,当主要链路出现故障时,能够自动切换到备份链 |
CopyRight 2018-2019 实验室设备网 版权所有 |